Time Thief Watch Cap

Yarn: 12 ply yarn (worsted, 10-12 wpi, ) . You'll need between 80 and 90g for this hat. Best be safe and have two full 50g balls or equivalent.

Needles: 1 x 60cm (23") 4.5mm circular needle (US & Imperial size 7); 1 set 4.5mm dpns. The whole hat can be knitted on dpns if you prefer.

Notions: 1 darning needle for the endy bits, 1 stitch marker of choice.

Tension: 19sts to 10cm (4") not absolutely crucial but should be within a stitch either way

Time investment: About 3 hours.

Big Brain Box Size (23-24" head)
Cast on 88 stitches, place marker and join in the round. Remember to slip marker from left to right hand needle at the end of each round.

Band
Round 1: *K2, p2 , repeat from *
Rounds 2-12: as for round 1
Round 13: Knit this creates a turning ridge for the brim
Round 14-16: as for round 1

Body
Round 17+: Commence stocking stitch (just knit and knit and knit). When whole work measures 20cm (8"), begin decreases.

Decreases:
Round1: *K6, K2tog, repeat from *
Round2 (and all even rounds): knit
Round3: *K5, K2tog, repeat from *
Round5: *K4, K2tog, repeat from *
you'll need to change to dpns about here
Round7: *K3, K2tog, repeat from *
Round9: *K2, K2tog, repeat from *
Round11: *K1, K2tog, repeat from *
Round13: *K2tog, repeat from *

Finishing:
Cut wool leaving a tail of about 10cm (4"). Thread tail onto darning needle and run through all remaining stitches. Remove dpns and draw tail tightly. Pass the threaded needle through the cat's bum at the top and weave in. Weave in the cast on tail. Turn up the brim at the turning ridge and c'est finis.


I'm a Lady Size (21-22" head)

Cast on 80 stitches, place marker and join in the round. Remember to slip marker from left to right hand needle at the end of each round.

Band
Round 1: *K2, p2 , repeat from *
Rounds 2-10: as for round 1
Round 11: Knit this creates a turning ridge for the brim
Round 12-14: as for round 1

Body
Round 15+: Commence stocking stitch (just knit and knit and knit). When whole work measures 17.5cm (7"), begin decreases.

Decreases:
Round1: *K6, K2tog, repeat from *
Round2 (and all even rounds): knit
Round3: *K5, K2tog, repeat from *
you'll need to change to dpns about here
Round5: *K4, K2tog, repeat from *
Round7: *K3, K2tog, repeat from *
Round9: *K2, K2tog, repeat from *
Round11: *K1, K2tog, repeat from *
Round13: *K2tog, repeat from *

Finishing:
Cut wool leaving a tail of about 10cm (4"). Thread tail onto darning needle and run through all remaining stitches. Remove dpns and draw tail tightly. Pass the threaded needle through the cat's bum at the top and weave in. Weave in the cast on tail. Turn up the brim at the turning ridge and c'est finis.

Things you might like to know about how I knit this pattern.

• It's called the Time Thief Watch Cap because, quite literally, I knit it in stolen time - walking to work, standing in queues, during staff meetings, at red traffic lights (shhh) etc... It takes about 30 mins for the cast on and final decreases time, the rest is bonus knitting time.


• The fabric is meant to be reasonably tight to increase the moisture repelling properties and warmth of the hat.


• I used a cable cast on, you can use whatever method you prefer.


• I hate joining in the round so I knit the first round as a row and join at the beginning of the second round. The small gap is sewn together at the end with the tail from the cast on.


• I don't use a marker until the decreases as it slows me down. The cast on tail indicates the beginning of a round until that point.


• To change sizes, go up or down in multiples of 8 stitches. 72 stitches, for example, would be good for a kid's size.


• There is no pattern for the stripes - I just make it up depending on the amount of wool available.